- Fuel cell test fixture is suitable for use with 5 cm2 and 25 cm2 area cells
- Configuration for liquid fuels is available. All wetted components of the liquid side are non-metallic and highly chemically resistant
- Gold plated copper current collectors
- Anodized aluminum end plates (2) with reactant input/output ports, stainless
steel Swagelok® compression fittings, cartridge heaters and thermocouple well - Cell heaters, Gaskets, gasket templates and additional hardware such as bolts, washers, fittings and o-rings
PEM
- Single cell – 50 cell stack
- Active area – 100 cm2 / 286 cm2
- Power – Up to 10kW
Alkaline
- Single cell – 48 cell stack
- Active – 100 cm2 / 700 cm2
- Power – Up to 10 kW
- Power consumption: 2.5 kWh – 1 MWh
- Gas production per hour: 500L – 20000L
- Oxygen gas: 250L – 10000L
- Adjustable pressure: Maximum 5 barg
- Purity of gas: Hydrogen gas 99.7% – 99.9%, Oxygen gas 98%
- Single Cell & Stack
- Fuel cell
- Redox Flow Cell
- AEM / PEM /CO Electrolyzer
- High pressure (up to 30 bar) NREL-certified Electrolyzer
- Compressible type
- Active area: 5 – 256 cm2
- Flow Field
- POCO Graphite, Platinised SS / Ni
- SS / Anodised AL end plates
- Cu current collectors
- Sheet assembly reduces offset accumulation error
- Different production lines can correspond to different MEA designs
- Assembled in sheets for efficient use of materials
- Low scrap rate and low consumption
Standard MEA Size Preparation 25 / 50 / 100 cm2
Ultrasonic Spray Coating Machine
- PEM, GDL, Electrode and Electrolyte coating
- Coating area: 400mm x 400 mm
- 3-Axis Precision coating
- Vacuum / Heated Plate
- Thickness of the film: 100 nm – 100 μm
- Flow rate: 0.5 – 10 ml/min
- Self-cleaning ultrasonic nozzle
- Optional: Inert chamber, Camera vision system, Ultrasonic dispersion liquid supply system
- Applications: Fuel Cell, Electrolyzer, Spray Pyrolysis etc.
Desktop CCM Spray Equipment
- Vacuum table with heating functions
- Low pressure, low air volume spray process
- High material utilization
- Air atomising spraying
- Maximum dimension: 400 mm x 400 mm
- Spraying rate: 1 ~200 mm/s
- Repeat Accuracy: ±1 mm
- Spraying path: S-shaped design
- Mold size: 30 cm x 30 cm
- Temperature: 300 oC (Optional 500 oC)
- Multi-range temperature controller
- Pressure range: Up to 30 Ton
- MEA – 5 / MEA – 7 Automatic assembly
- Final inspection
Automatic / Manual Heated Press
- Four-column lifting pneumatic cylinder design
- Heating temperature: 180 (Maximum)
- Total cylinder output: 480 / 1400 kgf
- Hot pressing time: 0 – 999 Seconds
- Mold size: 180 mm x 180 mm
- Catalyst slurry preparation
- CCM coating
- Raw material preparation (GDL / Boarder)
- GDL glue dispensing
- MEA-5 / MEA-7 Automatic assembly
- Final inspection
MEA-5 Semi-auto Assembly
- CCM Boarder assembly process
- Low/High temperature assembly with optical position function
- Frame: 600 x 300 mm
- CCM Area: 400 x 300 mm
- Alignment accuracy:
- Roller heating: Maximum 80 oC
MEA Leak Test
- Barcode reading function
- Leakage true value measurement
- True value cannot be converted into flow value simultaneously
- Sample size: 450 x 300 mm
- Mold size: 560 x 350 mm
- Test pressure: 0.1 – 0.5 kg/cm2
- Pressure test accuracy: ± 0.001 kgf/cm2
- Pressure difference detection range: 0 – 35kPa
- Pressure difference accuracy: ± 0.05kPa
850 Multi-Range Fuel Cell Test System
- Multiple current range: 5A / 25A / 50A or 10A / 50A / 100A
- Electronic load: 100W, 20V
- Suitable for up to 50cm2 PEM cells
- Automatic control of purge gas to the cell
- Computer controlled cell operation & experimentation
840 Advanced Fuel Cell Test System
- Ideal for large area single cell cells & short stacks
- Electronic Load: 500W, 20V, Current Range: 12A / 62A /125A or 25A / 125A / 250A
- Electronic Load: 1kW, 20V, Current Range: 50A / 250A / 500A
- Impedance Spectroscopy & HFR option
620 Alkaline, PEM & AEM Water Electrolysis Test System
- 4 Current range potentiostat ± 0.07A, 0.7A, 7A, 20A, ±5V, 100W
- Programmable power supply for operation up to 100A, 5V, 500W
- Impedance Measurement Types – Sweep EIS and Single-Freq HFR Real-Time Measurement
740 Membrane Test System
- Measurement of the through-thickness membrane resistance and conductivity as a function of temperature, humidity level and pressure
- Uses bare (non-catalyzed) membrane
- Small sample size 6mm x 30 mm
857 RFB / 670 Electrolysis Workstation
-
- 0.07A, 0.7A, 7A, 20A current range
- Electrolyte reservoirs, stirring, and temperature control
- EIS range: 1mHz to 100kHz
845 / 855 SOFC / SOEC Test system
- Suitable for Button cell, Planner cell & Short stack
- Zero volt load
- Furnace controller with redundant
- Over temperature controller
Fuel Cell Stack Test Station
- Current range ≤ 2000A
- Voltage range ≤ 800V
- Power ≤ 300kW
- Optional: CVM, EIS, Automatic
- Back pressure control
SOFC / SOEC Stack Test Station
- Load Bank: FC Mode
- Power Supply: EC Mode
- Including EIS, CVM, Reformer and Furnace
Electrolyzer Test Station
- Alkaline / PEM / AEM Water Electrolysis
- Power Supply, Potentiostat and Impedance Analyzer
- Power: Maximum 500 kW
- Current: 10000A
- Optional: Automatic Back Pressure Control, H2 in O2 and O2 in H2 Sensors
Mega EIS System
- Input Voltage: Up to 1000V
- Input Current: Up to 2000A
- Frequency Range: 1mHz – 100 kHz
- Number of channels: Up to 1024
Cosumables: Fuel Cell / Electrolyzer / RFB
- Membrane: Anion Exchange Membrane / Cation Exchange Membrane / Bipolar Membrane
- Gas Diffusion Layer (GDL): Carbon paper / Cloth Metal Foam / Mesh
- Catalyst: Pt – C / Pt – RuC / Pt – Lr / Pt – Pd / Pt – Ni
- Gasket: Teflon / Silicon / Mylar
- Gas Diffusion Electrode (GDE): PtC Coated GDL / Pt – Ru Coated GDL
- All stainless steel construction – regulators, condensate collection tanks, tubing and fittings
- Dual channel with isolated flow paths
- Independently control or balance anode & cathode pressure
- Accurate pressure control (±3.5 kPa or 0.5 psi) & stability from 0.1 – 10 SLM
- Integrated potentiostat for 840 /850 / 855, Series Fuel Cell Test Systems / 890 Series Fuel Cell Test Loads
- 3 current ranges for maximum flexibility and current accuracy 2 A, 200 mA, 20 mA (2A models) and 5 A, 500 mA, 50 mA (5A models)
- ZView® included for EIS data analysis
- Optional FRA for EIS measurements (1mHz to 40 kHz)
- It can integrate with the 600/840/850/855/857/885/890/910 test systems
- The 881 FRA and FuelCell® software provides continuous, single-frequency High Frequency Resistance (HFR) and Electrochemical Impedance Spectroscopy (EIS) analysis of an operating fuel cell
- HFR can be performed with the current interrupt (IR drop) measurement to determine the cell’s internal or ohmic resistance
- It can be integrated with the Model 910 Multi-Channel Microelectrode Analyzer (MMA) for impedance spectroscopy of electrode and sensor arrays
- It is a computer-controlled system featuring automated gas switching
- Automatic selection of one of 3 gases each for the Anode & Cathode from FuelCell® software
- Combine with 885 Potentiostat for fully-automated Crossover, ECSA & other diagnostics
- Automatic Water Fill Method (requires water feed at 30 PSIG min. or 20 PSIG above back pressure)
- 892 Data Acquisition Expansion System
- Increase the input capabilities of the 840, 850C/e and 890C/CL/e series of fuel cell test systems
- 8 Voltage or Current inputs & 8 thermocouple inputs
- Directly supported by FlowCell® software
- Plug-and-Play Accessory for 850/855/840 Fuel Cell Test Systems.
- Mounting for up to 5 mass flow controllers (MFCs)
- Integrated control of gas mixture type and composition in FuelCell® software
- Connectors for up to 3 MFCs and External Alarm Input
- Heated cuffs are an important accessory for PEMFC testing
- Eliminate cold spots that cause condensation
- Designed for 850/840 Fuel Cell Test Systems & PEMFC hardware
- Easy-to-install, low power and safe to use
- Ideal for gas mixing experiments including reformate simulation and contaminant / poison studies
- Ideal for independent control of additional gas dew point
- Designed for flows up to 5 SLPM
- Stainless steel humidifier with integrated heated & insulated flexible Swagelok gas transfer line